Installing A Bath tub
Installing A Bath tub
Blog Article
They are making a number of great points on the subject of Tools You Need to Install a New Bathtub as a whole in the content directly below.
Mounting a bathtub isn't specifically rocket science, but it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open a wall surface to eliminate the old bathtub and position the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. Make certain you have qualified on your own for the job as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration utilizing one prior to you start. Chances are you might require a professional plumber to make tube links.
This write-up will assist you mount a new tub in your washroom if you have actually currently bought a new bathtub and also don't need to transform the setup of your previous water supply pipes.
Your devices and also product checklist must consist of the following:
Getting ready for the Setup
To start with, the supporting frame supplied with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic due to the limited gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, put the bathtub in the called for setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait until the bathtub has been made use of at least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in area in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, triggering the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I think sharing that editorial was a good idea. Don't hesitate to set aside a second to share this post if you appreciated it. Thank you so much for going through it.
Go Company
Report this page